Time-Resolved Fluorescence Wiki

using_the_antibunching_script

Anonymous (anonymous@undisclosed.example.com) — 2014-06-19T07:40:32+00:00

2014/06/19 09:36		current
Line 1:		Line 1:
	{{tag> antibunching howto tutorial correlation analysis SymPhoTime}}		{{tag> antibunching howto tutorial correlation analysis SymPhoTime}}
-	~~TOC~~	+	~~NOTOC~~

	====== Antibunching Analysis ======		====== Antibunching Analysis ======
Line 9:		Line 9:

	This tutorial shows step-by-step, how to calculate an antibunching curve from a fluorescence time trace of a single emitter, in this example a nanodiamond NV center, excited with a pulsed 530 nm laser.		This tutorial shows step-by-step, how to calculate an antibunching curve from a fluorescence time trace of a single emitter, in this example a nanodiamond NV center, excited with a pulsed 530 nm laser.
		+
		+	{{ youtube>bEyhuWnmFC4?large }}

	===== Background Information =====		===== Background Information =====
Line 77:		Line 79:

	* Here it is impossible to determine the number of emitters. In this measurement the luminescence stems from several emitters.		* Here it is impossible to determine the number of emitters. In this measurement the luminescence stems from several emitters.
-

Anonymous (anonymous@undisclosed.example.com) — 2025-04-09T14:01:09+00:00

2025/04/09 16:00		current
Line 5:		Line 5:
	====== How to Perform Antibunching Measurements ======		====== How to Perform Antibunching Measurements ======

-	Antibunching Measurements are (normally) measured in T2 mode. In T2 mode, all input channels of the TCSPC electronics are treated the same, also the "Sync" channel. Therefore the sync has to be disabled either by disconneting the cable, or by changing the CFD level or trigger level to such a value that the sync is not recognized any more. i.e. Sync rate = 0 . Directly in the Sepia software, the sync out can also be disabled.	+	Antibunching Measurements are (normally) measured in T2 mode. In T2 mode, all input channels of the TCSPC electronics are treated the same, also the "Sync" channel. Therefore the sync has to be disabled either by disconneting the cable, or by changing the CFD level or trigger level to such a value that the sync is not recognized any more. i.e. Sync rate = 0 . Directly in the Sepia software, the sync out can also be disabled.

	The descriptions below only mention physically disconnecting the sync. This is strictly necessary only for the PicoHarp 300 because it only has two channels.		The descriptions below only mention physically disconnecting the sync. This is strictly necessary only for the PicoHarp 300 because it only has two channels.

Anonymous (anonymous@undisclosed.example.com) — 2018-04-19T12:11:55+00:00

2018/04/19 14:11		current
Line 9:		Line 9:
	see also [[wp>Nitrogen-vacancy center]]		see also [[wp>Nitrogen-vacancy center]]

-	{{ howto:model_nv-centers.png\|Figure1: Model of the nitrogene vacancy in the diamond lattice}}	+	[{{ howto:model_nv-centers.png\|Figure1: Model of the nitrogene vacancy in the diamond lattice}}]

	==== Excitation ====		==== Excitation ====

Anonymous (anonymous@undisclosed.example.com) — 2026-01-12T10:25:53+00:00

2023/02/23 09:12		current
Line 53:		Line 53:

	[[howto:antibunching_measurements\|Photon antibunching measurements]]		[[howto:antibunching_measurements\|Photon antibunching measurements]]
		+
		+	[[howto:burst_duration_and_fcs_diffusion_time:burst_duration_and_fcs_diffusion_time\|Burst Duration and FCS Diffusion Time]]


Line 62:		Line 64:

	[[howto:calculate_ratiometric_single_pair_fret_distributions\|Calculate ratiometric single pair FRET distributions]]		[[howto:calculate_ratiometric_single_pair_fret_distributions\|Calculate ratiometric single pair FRET distributions]]
		+
		+	[[howto:burst_duration_and_fcs_diffusion_time:burst_duration_and_fcs_diffusion_time\|Burst Duration and FCS Diffusion Time]]

Anonymous (anonymous@undisclosed.example.com) — 2022-02-01T11:32:53+00:00

2022/02/01 11:54		current
Line 7:		Line 7:

	==== A decay caused by correlation statistics ====		==== A decay caused by correlation statistics ====
		+
		+	[{{howto:slope.png ?478x300\|Fig. 1: Baseline decay }}]
		+
	This decay is caused by correlation statistics. This happens because you correlate the first arriving photon against a photon at the longer time, which will be an increasingly unlikely event because the earliest stop photons always win and the experiment restarts.		This decay is caused by correlation statistics. This happens because you correlate the first arriving photon against a photon at the longer time, which will be an increasingly unlikely event because the earliest stop photons always win and the experiment restarts.

-	I attached a simulation.	+	A simulation with 90ns dead-time period:

-	[{{howto:logf.png?320x240\|Fig. 1: Logfile logf.png }}]	+	[{{howto:logf.png?320x240\|Fig. 2: Simulation }}]

Anonymous (anonymous@undisclosed.example.com) — 2018-06-25T07:18:07+00:00

2018/06/25 09:17		current
Line 32:		Line 32:
	[[video_tutorials#Kurt Thorn: Optical Sectioning and Confocal Microscopy\|Confocal microscoy and optical sectioning by Kurt Thorn]]		[[video_tutorials#Kurt Thorn: Optical Sectioning and Confocal Microscopy\|Confocal microscoy and optical sectioning by Kurt Thorn]]

-	[[technical docs:Beampath of the Zeiss LSM880]]	+	[[Beampath of the Zeiss LSM880]]

	[[howto:check_overlap_of_different_color_confocal_volumes\|How to check the overlap of different color confocal volumes]]		[[howto:check_overlap_of_different_color_confocal_volumes\|How to check the overlap of different color confocal volumes]]

Anonymous (anonymous@undisclosed.example.com) — 2024-10-11T08:30:57+00:00

2023/02/17 13:43		current
Line 1:		Line 1:
	{{tag>MicroTime LSM Theory SymPhoTime FCS Correlation}}		{{tag>MicroTime LSM Theory SymPhoTime FCS Correlation}}

-	~~TOC~~	+

	====== Introduction to Fluorescence Correlation Spectroscopy ======		====== Introduction to Fluorescence Correlation Spectroscopy ======